Australia Wide Delivery - 100% Australian Owned

How to install skirting boards

Everything you need to know in an easy to follow steps and video guides.

 

Installing skirting boards

Tools

  • Pencil
  • Tape measure
  • Paint scraper
  • Stud finder
  • Square
  • Rubber mallet
  • Combination saw
  • Coping saw
  • Fixing gun
  • Saw tools
  • Kwik Grip clamps
  • Intense power glue ADH4
  • Cordless glue gun
  • Skirting boards
  • Nails or glueh

Step-by-step visual guide for installation of skirting boards

1 Prepare the Wall

Removing any loose/flaky paint or irregularities from wall surface with a paint scraper. This step isn’t required on new walls.

2 Determine the stud location for a standard plaster wall

If renovating, you can see the previous nail fixings were located. Mark the wall above where the new skirting will be located. If a new plaster wall use a stud finder.

Typically, studs are at 450mm or 600mm spacings

3 Installing the first piece of skirting

Determine the first piece of skirting to be installed. We recommend that you work from left to right inside each room. For example. If you are on the inside of a room and looking out the door opening, install the first piece of skirting to the right side of the door opening and continue to work around the room from that point. This works with the Fast Trim method. The internal scribe joints are always on the left-hand end of the skirting board.

Measure first length of skirting board to be installed. This piece normally requires a square cut on both ends. Fit skirting and nail or glue in place.

4 Installing the rest of the room

Measure from the face of the skirting on the left to the wall on the right.

Scribe the left-hand end of skirting board. Cutting a scribe joint

Installing second piece and subsequent pieces of skirting boards

  • transfer the length measurement from the straight part of the scribe cut, to the right-hand end of the skirting. On a long length of skirting you may add 2mm to the overall length of skirting board, as this will make a tighter and neater fit for the scribe joint.
  • Cut the square cut on right-hand end of skirting board.
  • Install skirting board by positioning in place, ensuring the internal scribe joint in the corner is a neat fit where it meets the adjacent skirting, already installed.
5 Fixing the Skirting to the Wall

Nail method

Fit and fix in place by nailing through the skirting and plaster lining, into the framework studs.

OR

Glue method

Run two beads of Intrim Intense Power adhesive on the back of skirting board and place in position against wall and use a rubber mallet to tap along the length of the skirting to fix in place. No fixings required therefore minimal preparation required prior to painting.

The traditional method of cutting a scribe joint

Cutting a scribe
Step 1

Roughly mark the direction of the cut on the end of the skirting that you want to perform the internal mitre scribe joint.

Step 2

Tilt combination saw over on 43 degrees (a little less than 45 degrees) in the direction as marked in previous step and crosscut at 90 degrees.

Step 3

Mark the mitre and face cut intersection line with pencil.

Step 4

End for end the skirting board so that you are cutting from the face side all the time.

Step 5

Perform the 90-degree cut on the flat section of the skirting board and tilt saw over on 5 degrees (this is called back cutting and makes for a neater internal joint when installed.)

Step 6

Take this straight cut through to the point of where the profile or patterned section of the skirting begins.

Step 7

Clamp or support the end of the skirting board that the scribe joint is to be scribe cut with a coping saw

Step 8

Proceed to start cutting profile (the profiled section of the skirting is typically at the top portion of the skirting) section of skirting with coping saw, starting from top of skirting board being careful not to snap the very thin section of the skirting left on the top edge

Step 9

Continue to cut the profile section on the cut intersection point, with the coping saw positioned on a slight back angle from the face of cut, to produce an under cut or backing angle

Step 10

You will find the cutting easier, if you come in from each side of profiled section as shown on video.

Step 11

The final cut with the coping saw, is finished by completing the straight back cut that was performed by the combination saw

Step 12

Position offcut of skirting board onto the end of the scribe cut to confirm neat fit

The Fast Trim method of installing skirting boards

Fast Trim is a revolutionary new method allowing you to order pre-scribed skirting for your selected skirting design. Save time, save money, and achieve a high quality finish.

Learn More

Back to quick links

Get a free quote today

We aim to turn around quotes within 1 business day!

    Next
    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    Get a free quote today

    We aim to turn around quotes within 12 hours!

    How can we help?

    Enter your details below to let us know how we can help with your enquiry

    Free design consultation

    Enter your details below to let us know how we can help with your enquiry

     

    Sample basket
    Maximum of 4 samples


    Empty

    Available
    1 of 4

    Empty

    Available
    2 of 4

    Empty

    Available
    3 of 4

    Empty

    Available
    4 of 4

    Product basket


    Need technical drawings?
    Tick here if you require technical drawings of your selected profiles.


    Send me the Profiles Catalogue
    Tick here if you would like to order a hard copy of our Bespoke Moulding Profile Book showing a wide range of profiles and styles for your library.


    Alternatively you can download a PDF copy of the profile guide here.

    Download PDF brochure

    Specification Sheet
    Store all your favourite profiles here.


    Specification Sheet

    Quote Request
    Store all your favourite profiles here.


    Quote Request
    COVID-19 announcement : Our Sydney (Picton) office and showroom is currently not allowing visitors on site. Virtual appointments are available.